SERVICES

Commercial New Construction Electrical

Ground-up wiring for offices, retail, and warehouse shells, coordinated with your general contractor from slab rough-in through commissioning. We size the service for the loads you will actually run, then leave documented spare capacity for whatever comes next.



• Load calculations and panel schedules
• Rough-in through final inspection
  

Tenant Improvements & Electrical Build-Outs

Turning an empty suite into a working space means new lighting layouts, added circuits, data pathways, and demising walls that respect working clearances. We have delivered fit-outs for retailers and fitness brands across Georgia without missing an opening date.



• Existing panel capacity verified first
• Lighting, power, and low-voltage pathways
  

Commercial Electrical Troubleshooting

Nuisance trips, flickering LEDs, warm breakers, and voltage that sags every time a compressor kicks on. We trace the fault to its source with meters and thermal imaging rather than replacing components until the symptom disappears on its own.



• Thermal imaging and load logging
• Written findings after every call
  

Switchgear Installation & Upgrades

Gear that controls, protects, and isolates your building's power deserves more than a like-for-like swap. We assess interrupting ratings, plan the changeover around your operating hours, and stage temporary power so the lights stay on during the cutover.



• Interrupting ratings verified against fault current
• Cutover planned around your operating schedule
  

Commercial Panel & Distribution Upgrades

When breakers sit at capacity and there is nowhere left to land a circuit, the panel is the bottleneck. We measure real demand before recommending amperage, then upsize distribution with room left for equipment you have not bought yet.



• Recorded demand study before sizing
• Sub-panels, feeders, and distribution gear
  

Commercial Lighting & LED Retrofits

Swapping metal halide for LED cuts lighting energy by half or better and drops cooling load along with it. We handle fixture selection, occupancy controls, emergency egress compliance, and the paperwork your utility rebate program asks for.



• High-bay, troffer, and exterior fixtures
• Controls and egress lighting compliance
  

Electrical Panel Upgrades & Replacements

Federal Pacific and Zinsco panels, fuse boxes, and 100-amp services that ran out of room years ago. We swap the panel, bring branch circuits under current AFCI and GFCI rules, and coordinate the reconnection with your utility.



• Most swaps finished within one day
• Permit, inspection, and reconnection handled
  

Residential Electrical Repairs

Half the house dark with no tripped breaker, a receptacle that runs warm, a switch that buzzes. Small faults rarely stay small, so we find the loose connection or damaged conductor and fix it rather than patching around it.



• Dead circuits, trips, and warm devices
• Repairs brought up to current code
  

Whole-Home Electrical Rewiring

Knob-and-tube and mid-century aluminum branch circuits are why insurers ask questions. We replace the wiring room by room, add grounded and tamper-resistant receptacles, and open only the drywall the route genuinely requires.



• Phased so you can stay in the house
• Grounded, AFCI-protected branch circuits
  

EV Charger Installation

A Level 2 charger on a dedicated circuit adds roughly 180 miles overnight, which is most of a week of commuting. We verify panel capacity, run the circuit, mount the unit, and file the permit before the inspector arrives.

• Hardwired units and NEMA 14-50 receptacles
• Georgia Power rebate paperwork support
  

Lighting & Ceiling Fan Installation

Recessed cans, under-cabinet strips, chandeliers on high ceilings, and paddle fans that need a box rated to carry them. We set fixtures level, wire dimmers that will not buzz, and leave switch plates sitting flush.

• Fan-rated boxes and proper bracing
• Dimmer and LED compatibility checked
  

Outlet & Switch Installation

Adding a receptacle where the furniture actually sits, converting two-prong outlets legally, or putting a smart switch where no neutral exists. We handle the circuit work behind the plate so the device is safe and code-compliant.

• GFCI, AFCI, and tamper-resistant devices
• Three-way, dimmer, and smart switches